Volume Converter
Liters To Gallons, Cubic Feet And More
This volume converter turns liters to gallons, milliliters, cubic meters, cubic feet and fluid ounces as you type. So one figure shows up in every unit at once. It also keeps US and imperial units apart, uses the exact factor for each, and prints it so you can check the maths. Because it all runs in this tab, nothing you type is uploaded or stored.
- FreePrice
- Metric + US + imperialUnits
- Both waysDirection
- NoneUploads
Volume Converter
Liters, gallons, cubic feet, pints and more, all from one value
- Milliliter
- Liter
- Cubic centimeter
- Cubic meter
- Cubic inch
- Cubic foot
- US gallon
- US quart
- US pint
- US cup (kitchen measure)
- US fluid ounce
- Imperial gallon
- Imperial pint
- Imperial fluid ounce
Type a value to see it in every unit.
What A Liters To Gallons Converter Does
A volume is a length times a length times a length, so its unit is a cube. Therefore, the factor between two cubic units is their length factor cubed. The liter, in turn, ties straight to the metric cube. So the whole job is picking the right factor and multiplying by it.
That is what this volume converter does for you. Because it holds the exact factor for every unit, it turns liters to gallons, or cubic meters into cubic feet, with no drift from a half-remembered decimal. For more detail, see the Wikipedia article on the liter.
Next to each answer, it shows the factor it used. For example, a US gallon is 3.785411784 liters, while an imperial gallon is 4.54609 liters. The page names which one it used, so the gallon is never a guess.
It converts in every direction at once. So you type one value, and every metric, US and imperial unit updates together. That saves looking up one pair at a time.
Nothing leaves this tab, either. Hence a figure from a recipe, a tank spec or a shipping box is safe to type, because the maths happens in your browser and the page stores nothing.
How Liters To Gallons Conversion Works
First, the converter reads your number and its unit. Then it turns that value into liters, the base unit, because every volume has a fixed factor to and from the liter.
Next, it sends that value in liters out to every other unit. So one step to the base and one step back covers each pair. That is why all the boxes agree at once.
The metric cube is the clean anchor. A liter is a cube 10 centimeters on each side. As a result, a cubic meter holds 1,000 liters, and a milliliter is one cubic centimeter.
The page also keeps far more digits than it shows. Therefore, the rounding on screen never feeds the next step. A round trip from liters to gallons and back lands on the number you started with.
US Or Imperial? Which Gallon You Mean
The word gallon names two different volumes. A US gallon is 3.785 liters, while an imperial gallon is 4.546 liters. So the gap is about a fifth.
The same split runs through the pint and the fluid ounce. For example, a US pint is 16 US fluid ounces, but an imperial pint is 20 imperial fluid ounces. So even the ounce count differs.
That is why the page labels each one. A bare gallon is ambiguous, so the converter shows the US and the imperial gallon as separate boxes instead of guessing which you meant.
In short, pick the system you mean. Still, the converter keeps both, so a US recipe and a British one both come out right when you convert liters to gallons.
Liters To Gallons And Other Metric, US And Imperial Units
The metric units step by thousands. So a milliliter is a cubic centimeter, a liter is 1,000 milliliters, and a cubic meter is 1,000 liters.
Cubic units cube their length. For example, a cubic foot is 0.3048 cubed cubic meters, or about 28.32 liters, because volume cubes the step.
The US liquid units sit on the US gallon. So a quart is a quarter of it, a pint an eighth, and a fluid ounce a 128th.
The imperial units sit on the imperial gallon. Hence the imperial pint and ounce are larger than their US namesakes, and that is the common trap.
What This Volume Converter Will Not Do
It will not measure a container. The page converts one volume figure that you type, so it does not work out a box's capacity from its sides.
It will not blur US and imperial units. A gallon, a pint and a fluid ounce differ between the two systems, so the page names each one instead of printing a bare word.
It will not promise exact cooking cups. A cup varies by country and by habit, so the page uses the standard US figure and treats a cup as the rough measure it is.
It will not round away your precision. The full value stays behind the scenes, and only the display is rounded to the decimals you choose. So nothing drifts between steps.
Watch the Volume Converter in Action
A short video walks through every step. Then pick your language below, and turn on captions if you like.
How To Convert Liters To Gallons Here
Four steps, and none of them need an account.
- 1
Type the volume
Type any number, decimals included. Because the converter reads as you type, the other units fill in before you finish.
- 2
Pick the unit you typed
Then pick the unit you typed, US or imperial where it matters. Since every box updates together, you only set the one you started from.
- 3
Read every unit at once
Next, read the matching value in each other unit, with its factor shown. So the answer and the maths behind it sit side by side.
- 4
Copy or round as you like
Finally, choose how many decimals to show and copy the result. After that, the figure is ready for your recipe, your tank or your box.
Why Use This Volume Converter
Five reasons, and each one saves a lookup.
It keeps US and imperial apart
Because the word gallon means two volumes, the page gives each its own box. So a US recipe and a British one both come out right.
It converts every unit at once
One value feeds every unit, so you never convert one pair at a time. Therefore, liters to gallons and gallons back to liters sit on the same screen.
It shows the exact factor
Each answer shows the factor it used. Hence you can check the maths yourself instead of trusting a black box.
It keeps full precision
The page rounds only what it shows, not what it stores. As a result, a round trip returns the number you began with, with no drift.
Nothing uploads
The whole job runs in this browser tab. So a figure from a recipe or a tank spec is safe to type, and it leaves no trace.
Habits That Keep Volume Maths Right
Six habits that keep a conversion honest.
- Say US or imperial A gallon, a pint and an ounce differ between the two systems. So name the system, because the bare word is wrong about as often as it is right.
- Write the unit next to the number The number 5 on its own means little, but 5 liters is clear. Because a bare number hides the unit, a label stops a mix-up.
- Cube the length factor for cubic units A cubic foot is the foot factor cubed. So for meters to feet in a volume, cube the step instead of using it flat.
- Round at the end, not partway Each early round nudges the answer a little. Hence keep the full value until the last step, which is what this page does for you.
- Treat a cup as approximate A cup is a rough, regional measure. So for careful work, use milliliters, which the page gives exactly.
- Sanity-check against something you know A liter is about 0.26 US gallons, and a cubic meter is 1,000 liters. So compare a surprising answer with those, and a slip shows up at once.
Six Ways Volume Conversions Go Wrong
None of these breaks the maths, which is exactly why they slip through.
Mixing US and imperial gallons
A US gallon is about a fifth smaller than an imperial one. So reading one as the other gets a tank or a fuel fill wrong.
Using the length factor, not its cube
A cubic foot is the foot cubed, not the plain foot. Therefore, a flat length factor undercounts a volume badly.
Forgetting the pint differs too
A US pint is 16 ounces, and an imperial pint is 20. However, both are called a pint, so the count catches people out.
Treating a cup as exact
A cup is approximate and regional. So a recipe that leans on cups changes from country to country.
Rounding too soon
An answer rounded at each step collects error. Hence a figure that looks exact can be off once several conversions stack up.
Reading milliliters as grams
A milliliter is a volume, while a gram is a mass. So they match only for water, and even then only roughly.
Liters To Gallons And Volume Converter Questions
Is this volume converter free?
Yes. There is no account, no limit and no paid tier. So you can convert as many figures as you like.
Does it upload what I type?
No. The whole job runs in this browser tab, and nothing is sent anywhere. So a figure from a recipe or a tank spec stays with you.
Which units does it cover?
It covers milliliters, liters, cubic centimeters and cubic meters, the cubic inch and foot, and the US and imperial gallon, pint and fluid ounce. So the common volumes all update from one value.
How do I convert liters to gallons (US)?
To convert liters to gallons (US), divide by 3.785411784. So 10 liters is about 2.64 US gallons, and the page prints that factor.
How do I convert liters to imperial gallons?
Divide the liters by 4.54609. So 10 liters is about 2.20 imperial gallons, the imperial side of the split.
What is the difference between a US and an imperial gallon?
A US gallon is 3.785 liters, while an imperial gallon is 4.546 liters. So say which one you mean, because the gap is about a fifth.
Is a milliliter the same as a cubic centimeter?
Yes, exactly. One milliliter is one cubic centimeter, so the two boxes always match.
How many liters are in a cubic meter?
Exactly 1,000. So 2 cubic meters is 2,000 liters, because a liter is a cube a tenth of a meter on each side.
How do I convert cubic feet to liters?
Multiply by about 28.3168. So 5 cubic feet is about 141.58 liters, because volume cubes the foot.
Why do two gallons exist?
The United States kept an older wine gallon, while Britain defined a new imperial gallon in 1824. So the two have not matched since.
Is a US pint the same as an imperial pint?
No. A US pint is about 473 milliliters, and an imperial pint is about 568. So the imperial pint is the larger one.
Can it convert a whole list at once?
No. It shows one figure in every unit at once. So convert values one at a time, which keeps each answer and its factor clear.
Does it round or truncate?
It rounds to the decimals you pick, and it rounds only the display. Therefore, the stored value stays exact for the next conversion.
Why do my hand maths differ slightly?
Usually because the wrong gallon was used, or a value was rounded too early. So pick the right system and keep the full value until the end.
How many US fluid ounces are in a US gallon?
There are 128. So a US fluid ounce is a 128th of a US gallon.
How big is a cup?
A US cup is about 237 milliliters, though a cup varies by country. So for careful work, use milliliters instead.
Does it need the internet after loading?
No. Because the factors are built into the page, it keeps working offline once the tab is open.
Does it work on a phone?
Yes. The boxes stack and stay large enough to tap, so a quick conversion works on a phone as well as on a desktop.
Does it find a tank volume from its sides?
No. It converts a volume you already have. So multiply the sides yourself first, then convert the result here.
Can I convert gallons to liters directly?
Yes. The page goes through liters for you, so you pick the US or imperial gallon and read the liters at once. Liters to gallons works the same way in reverse.
Does it do barrels or bushels?
It focuses on common volumes. So for a rarer unit like a barrel or a bushel, the all-units converter covers more.
What about my privacy?
Everything happens in the browser, so nothing you type is stored or sent. Of course, you can watch the network tab to confirm it.
Tools That Go With This One
Four pages the same work usually leads to.
The two-dimension sibling, where the factor is squared instead of cubed. Convert square meters, acres and hectares there.
Open tool →For mass instead of volume, convert kilograms, pounds and tons the same careful way.
Open tool →Need length, speed or temperature too? The hub puts every category in one place, with the same careful maths.
Open tool →Move a value between decimal, binary, octal and hex. Then a figure from code reads the same in every base.
Open tool →
Convert It, Then Carry On
Type a volume, pick its unit, and read it in every other unit with the factor below. Nothing is stored or uploaded, and US and imperial units stay apart.